DESIGNING FOR DISTANCE: COVID-19’S IMPACT ON A LOS ANGELES VOTE CENTER

Proceedings of the 2020 Winter Simulation Conference K.-H. Bae, B. Feng, S. Kim, S. Lazarova-Molnar, Z. Zheng, T. Roeder, and R. Thiesing, eds.

Nicholas D. Bernardo Gretchen A. Macht

Dept. of Mechanical, Industrial and Systems Eng

University of Rhode Island 260 Fascitelli Center
for Advanced Engineering 2 East Alumni
Avenue Kingston, RI 02881, USA

Jennifer Lather

Durham School of Arch. Eng. and Construction
University of Nebraska-Lincoln PKI 206C
1110 S. 67th Street Omaha, NE 68182, USA

Abstract

Due to the outbreak of COVID-19, concerns regarding public health and safety extend directly to elections;thus, in-person voting imposes new challenges for election administrators. This case study applies discrete-event simulation modeling to a COVID-19 election system and demonstrates that designing for processingchanges, such as social distancing and equipment sanitization, differs from traditional elections. Theseparation of provisional voter check-ins, which reduced average time-in-system (ATS) and maximumtime-in-system (MTS) in previous models, increased ATS (i.e., 54-65 minutes) and MTS (i.e., 75-100minutes) in COVID models. When provisional check-ins were separated and check-in stations wererelocated toward the vote center entrance, the ATS and MTS were significantly reduced (i.e., 9-19 minutesand 4-32 minutes, respectively). These findings indicate that election systems operating during COVID-19require specific considerations rather than generalized recommendations.

Introduction

Coronavirus (COVID-19) concerns regarding health and safety extend directly to elections. Despitealternative voting options (NCSL 2020), in-person voting is still available. Election administrators mustunderstand the impact that design decisions have on election planning and resource allocation, especiallywith COVID-19 safety precautions (i.e., social distancing, sanitization), to ensure healthy and safe elections(CDC 2020; CISA 2020). While these precautions are essential in mitigating the spread of COVID-19,methods for designing polling locations under new regulations are speculation, and the system impact ofthese decisions is mostly unknown. This case study explores the impact of strategies for COVID-19 throughdiscrete-event simulations (DES) of a Los Angeles County (LAC) vote center.

LITERATURE REVIEW

Researchers have applied basic queuing theory and simulation models in voting (e.g., Edelstein andEdelstein 2010); however, these approaches often lack the specificity and granularity to represent thecomplexity of voting process behaviors. DES is a well-established domain and has demonstrated such inmany applications, including healthcare and construction. Little research, however, has bridged the gapbetween election system research and advanced DES. This modeling approach is necessitated by thechanges to voting processes per COVID-19 safety regulations (NCSL 2020). This study seeks to assess theimpact of design decisions on an election system implementing COVID-19 specific changes.

CASE STUDY

Through a case study on a LAC vote center design, the impact on election systems implementing socialdistancing and equipment sanitization was investigated during the 2020 Presidential Primary Election. Thisstudy directly expands upon the DES models in Bernardo et al. (2020) to include COVID-19 regulations. COVID-19 model adaptations reduced equipment quantities (i.e., 75 ballot marking devices [BMD] to 25)and path capacities (i.e., limited capacity on the path to maintain 6' distance) due to social distancingrequirements and established an equipment sanitization process after each BMD use (i.e., triangulardistribution [10, 15, 25] sec.). All other model aspects (e.g., routing, processing times) were kept fromBernardo et al. (2020). Alternative COVID-19 models were compared to the COVID-19 Baseline model,each replicated 100 times, by generating 99.3% confidence intervals (CI) (Bonferroni corrected 95% CI)on the differences in performance (i.e., average time-in-system [ATS], maximum time-in-system [MTS]).

RESULTS

Results, shown in Table 1, indicate that vote center design can significantly impact ATS and MTS inCOVID-19 elections. Strategies that redirected voter flow and relocated check-in stations, both individuallyand in combination, did not differ substantially from the COVID-19 Baseline model. The separation ofprovisional voter check-in processing (SPP), individually and in conjunction with redirected, looping voterpaths (LVP), demonstrate significant increases in ATS (i.e., 54-65 min. and 54-66 min., respectively) andMTS (i.e., 75-100 min. and 75-101 min., respectively). The combination of all design strategies (i.e., movedcheck-in stations [MCS], LVP, and SPP) also demonstrated an increase in ATS (57-69 min.) and MTS (81-107 min.). The model that included relocated check-in stations and the separation of provisional check-insresulted in a significant reduction in ATS (9-19 min.) and MTS (4-32 min.)

Table 1: Significant model results.

Model Change in ATS (hrs) Change in MTS (hrs)
SPP -0.991 ± 0.094 -1.463 ± 0.206
SPP and LVP -1.003 ± 0.096 -1.471 ± 0.216
SPP and MCS 0.231 ± 0.090 0.297 ± 0.232
SPP, LVP, and MCS -1.045 ± 0.097 -1.562 ± 0.217
Note: p < 0.007. Calculated as (Baseline - Option), negative values are an increase in time, positive values are a reduction in time.

DISCUSSION AND CONCLUSION

In Bernardo et al. (2020), models that separated the provisional voter check-in process demonstratedsignificant reductions in ATS and MTS. In the COVID-19 models of this study, however, this change doesnot exclusively result in ATS and MTS reductions. Separating the provisional check-ins in the COVID-19model only demonstrates an improved system performance when combined with their relocation. Thesefindings suggest that design considerations beneficial in a traditional election may not be as applicable, ormay negatively impact system performance, in election systems with COVID-19 mitigation strategies inplace. More work is required to fully understand the impacts and interactions between COVID-19mitigation strategies and polling location design to inform resource allocation decisions and ensure votersare not disenfranchised by in-person voting.

References

Bernardo, N. D., J. Lather, and G. A. Macht. 2020. “Analysis of Layout Impacts on Resource Allocation for Voting: A Los Angeles
Vote Center”. Proceedings of the 2020 Winter Simulation Conference, edited by K.-H. Bae, B. Feng, S. Kim, S. Lazarova- Molnar, Z. Zheng, T. Roeder, and R. Thiesing. Piscataway, New Jersey: Institute of Electrical and Electronics Engineers, Inc.
CDC. 2020. “Coronavirus Disease 2019 (COVID-19): How to Protect Yourself & Others”. https://tinyurl.com/rnohcbc , accessed 11 th July.
Edelstein, W. A., and A. D. Edelstein. 2010. “Queuing and Elections: Long Lines, DREs and Paper Ballots”. In Proceedings of the 2010 International Conference on Electronic Voting Technology/Workshop on Trustworthy Elections, August 9 th -10 th , Washington, DC, 1-8.
NCSL. 2020. “COVID-19 and Elections”. https://tinyurl.com/y8vtsnk5, accessed 11 th July.
CISA. 2020. “#Protect2020”. https://www.cisa.gov/protect2020# , accessed 13 th July.